Just How to Remove as well as Replace a Tub.
Just How to Remove as well as Replace a Tub.
Blog Article
The article author is making several great points about Tools You Need to Install a New Bathtub overall in this article on the next paragraphs.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Setting up a bathtub isn't exactly rocket science, but it does require solid plumbing, carpentry, and sometimes, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably tough job. If the old tub is readily available, the project can move speedily; if you have to open up a wall surface to get rid of the old bathtub as well as position the new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly require a helper to move out the old tub and also embeded in the brand-new one. Ensure you have qualified on your own for the task as well as are comfortable attempting it. Instead of hiring a professional to take over a halfway-completed task, it is much better to think about employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your restroom if you have currently purchased a new bathtub as well as don't require to alter the arrangement of your previous water pipes.
Your devices as well as material list ought to comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The procedure of removing the existing faucets can be quite bothersome due to the limited access that is usually the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. When the supply pipelines have been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the new taps, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in area in between the tap and the sink. Protect the faucet in position with the manufacturer provided backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former type needs to be connected to the tap ends first, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 little factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub till the level reviews degree.
To mount faucets, fit the bottom of the furthest adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Activate the water system as well as check all joints and also new pipework for leaks and also tighten them if essential. Load the tub and also check the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the manufacturer's user's manual. Tiling as well as sealing around the bath tub ought to wait until the bath tub has been used at the very least once as this will resolve it into its last position.
Planning for the Setup
Firstly, the supporting structure supplied with the bath needs to be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bath and also the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be suited its final setting.
Tiling Around the Bath tub
In the area where the bath fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to split a rigid seal, triggering the water to pass through the wall between the bathroom and the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water before sealing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very serious about A Step-by-Step Guide to Installing a Bathtub and I am assuming you enjoyed the blog entry. For those who liked our blog post if you please don't forget to share it. Thanks for going through it.
Contact Us Report this page